Everyone has got their own unique piece of advice involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the job can relocate easily; if you have to open a wall surface to get rid of the old bathtub and position the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the job and also fit attempting it. Rather than employing a specialist to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This article will assist you set up a new tub in your shower room if you have actually already purchased a brand-new tub as well as don't need to alter the plan of your previous water pipelines.
Your devices as well as product list need to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the faucet in place with the supplier provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water and inspect all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill the tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub needs to wait till the tub has actually been made use of at the very least when as this will certainly resolve it into its final position.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about problems with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that short article was really helpful. If you please take a moment to promote this article if you appreciated it. Many thanks for taking the time to read it.
Need Help? Hire Us Now!